Saltar al contenido
Glosario November 2026 6 lectura de minutos

What Is Packet Loss in VoIP Calls?

Packet loss is voice data that never arrives, heard as clipped or robotic audio. See how RTCP counts it, how it differs from jitter, and what to check first.

D
November 2026
Última actualización

Respuesta rápida

Packet loss in VoIP is voice data that was sent but never arrived, heard as clipped, choppy or robotic audio. RFC 3550 defines the cumulative count as packets expected less packets actually received, and RTCP also reports the fraction lost since the previous report.

A voice call is a stream of small packets. Each carries a slice of audio. RFC 3551 sets the default packetization interval for audio at 20 ms or one codec frame, whichever is longer. When one of those packets never arrives, the slice of sound it carried is missing. That is packet loss, and it is one of the two network measurements, with jitter, that most often explains why a call sounds bad.

What Packet Loss Is

Packet loss is voice data that was sent but did not arrive. It can happen when a network link is overloaded, when a wireless connection is weak, or when equipment on the path drops traffic. Because RTP usually runs over UDP, there is no automatic resend. RFC 3550 says RTP does not guarantee timely delivery or quality of service. A lost audio packet is generally just gone, and the receiver has to cope.

How It Sounds on a Call

Listeners describe the effect in similar words: clipped syllables, words that drop out, robotic or metallic voices, and audio that stutters. Short gaps may be hidden by the receiving software, so mild loss can go unnoticed. As the gaps become more frequent or longer, the call becomes difficult to follow. Packet loss and jitter can sound alike, which is why it helps to measure instead of listening alone.

How RTCP Counts It

The RTP control protocol, RTCP, lets each receiver report what it saw. In the reception report block described in section 6.4.1 of RFC 3550, two fields cover loss:

  • Cumulative number of packets lost: the number of packets expected less the number of packets actually received, counted since the beginning of reception. The RFC notes that late packets are not counted as lost, and that the value may be negative if there are duplicates.
  • Fraction lost: the fraction of packets lost since the previous report, expressed as a fixed-point number with the binary point at the left edge of the field. This is how a single recent interval is told apart from the running total.

The "expected" count comes from RTP sequence numbers, which is why a receiver can notice a gap even though it cannot see the missing packet. These figures describe the stream as the receiver experienced it, which makes them more useful than a one-sided test.

Packet Loss vs Jitter vs Latency

  • Packet loss: packets that never arrive.
  • Jitter: packets that arrive, but with uneven spacing.
  • Latency: how long packets take, covered on the VoIP latency page.

A connection can have one without the others. Together with the códec in use, they feed the estimate behind MOS. This page does not give a loss percentage that counts as acceptable, because no figure is verified against a source here, and the effect varies with the codec and the receiving software. Compare against the quality your own agents and customers report.

What to Check First

  1. Is it one agent, one route or everyone? One agent suggests their local connection. One destination suggests a carrier route. Everyone suggests a shared link.
  2. The network path. Wi-Fi and busy shared connections are common places for loss to start.
  3. The trunk. Compare the same destination over another carrier if you have one.
  4. The codec. A heavier codec uses more bandwidth. Check the voice codec page before changing it.

DialerBee captures mean opinion score per call, and the fiabilidad de la plataforma page describes the media-node and failover design. A per-call view makes loss easier to localise than an overall average.

Preguntas frecuentes

What is packet loss in VoIP?

Voice packets that were sent but never arrived. Each missing packet is a gap in the audio, heard as clipped, robotic or dropped-out speech.

How is packet loss measured?

RTCP reports carry two figures: the cumulative number of packets lost, which is expected less received, and the fraction lost since the previous report. RFC 3550 defines both.

What is the difference between packet loss and jitter?

Packet loss is packets that do not arrive. Jitter is variation in the timing of the packets that do arrive.

What percentage of packet loss is acceptable?

There is no single verified figure. It depends on the codec and the receiving software. Compare your measurements with the call quality your users report.

Does packet loss cause one-way audio?

Not usually. One-way audio typically means media is not reaching one side at all. Loss makes audio choppy rather than silent.

Related terms and guides: jitter, MOS, voice codec, RTP, VoIP latency, fiabilidad de la plataforma, one-way audio troubleshooting.

Fuentes

Términos relacionados

¿Listo para ver DialerBee en acción?

Solicite una demostración en vivo de 15 minutos o comience una prueba gratuita de 14 días: sin presentaciones, sin compromiso. Las llamadas empiezan en cuanto su propia troncal SIP o PBX está conectada y aprobada.

Prueba gratuita de 14 días · crédito de IA gratuito · sin tarjeta · 11 idiomas · BYOC · controles que apoyan el cumplimiento

Ver el sitio completo en inglés →