What Is Jitter in VoIP?
Jitter is the variation in the arrival timing of voice packets. Learn how RTP measures it, what the formula means and how it affects call quality.
Risposta rapida
Jitter is the variation in how evenly voice packets arrive. RFC 3550 defines interarrival jitter as the mean deviation, smoothed, of the difference in packet spacing at the receiver compared with the sender, measured in RTP timestamp units. Packets sent at even intervals that arrive unevenly produce jitter.
Voice over IP sends speech as a stream of small packets, each sent at a regular interval. The network does not promise to deliver them at the same regular interval. Some arrive a little early, some a little late. That unevenness is jitter, and it is one of the network measurements behind how a call sounds.
The Definition
RFC 3550, the RTP specification, defines the interarrival jitter J as the mean deviation (smoothed absolute value) of the difference D in packet spacing at the receiver compared to the sender, for a pair of packets. Equivalently, it is the difference in the relative transit time of two packets, where the relative transit time is the difference between a packet's RTP timestamp and the receiver's clock at the time of arrival, measured in the same units.
For packets i and j with RTP timestamps S and arrival times R, the RFC writes D(i,j) as (Rj minus Ri) minus (Sj minus Si). The receiver updates its jitter estimate for each data packet as it arrives, using the formula J(i) = J(i-1) + (|D(i-1,i)| - J(i-1)) / 16. The RFC says the gain parameter of one sixteenth gives a good noise reduction ratio while keeping a reasonable rate of convergence, so the result is a smoothed running figure rather than a reaction to any single packet, and the current value is sampled whenever a reception report is issued. The RFC says the calculation must conform to this formula so that profile-independent monitors can interpret reports from different implementations.
Come funziona
The value is expressed in RTP timestamp units. For a narrowband audio codec whose clock runs at 8,000 ticks per second, which RFC 3551 gives for PCMU, PCMA and G.729 in its table of payload types, one tick is 125 microseconds. A reported jitter value of 80 therefore corresponds to 80 ticks, or 10 milliseconds. Always check the clock rate before comparing a number from one stream with another.
An Example
This is an illustration with invented numbers. Packets leave the sender every 20 milliseconds. At the receiver, the gaps between arrivals are 20, 20, 35, 5, 20 and 20 milliseconds. The average gap is still 20 milliseconds, but the 35 and 5 show variation. The jitter estimate rises when such differences appear and decays slowly as the spacing returns to normal. A stream with the same average spacing and no variation would report close to zero.
Why It Matters for Outbound and Inbound Teams
High jitter is heard as choppy or robotic speech, and it is one of the inputs that platforms use to estimate MOS, together with packet loss, latency and the codec. Because the cause is often on the network path between the endpoints rather than in the software, jitter can explain why one agent's calls sound worse than another's even though both use the same platform.
Agents on browser phones feel network variation on the last leg. The comparison of WebRTC and SIP phones e il Softphone WebRTC explainer describe what that means in practice. DialerBee captures mean opinion score per call in its operations center and surfaces low-MOS alerts on the wallboard, and the affidabilità della piattaforma page describes how media nodes, failover and load balancing are set up. Jitter is the kind of cause a per-call view helps you find.
How to Use It
- Look per call and per agent, not only overall. Problems cluster on one connection or one route.
- Convert units first. A raw number in timestamp units is only meaningful with the clock rate.
- Read it with packet loss and latency. Each has its own audible effect.
- Test the agent's last mile. Shared and wireless connections are a common place to look first.
Domande frequenti
What is a good jitter value for VoIP?
There is no single universal limit. Lower is better, and what is acceptable depends on the codec, the playout buffering and the call. Compare your own measurements against the quality your agents and customers actually report.
How is jitter different from latency?
Latency is how long packets take to arrive. Jitter is how much that time varies from packet to packet. A connection can have high latency and low jitter, or the reverse.
What unit is jitter measured in?
In RTP reports, RTP timestamp units. Divide by the clock rate to get seconds; for an 8,000 Hz clock, 8 units equal 1 millisecond.
Does jitter cause dropped calls?
Jitter affects how a call sounds rather than whether it connects. Severe variation is heard as choppy audio, and it is one of the inputs to a MOS estimate.
Who measures jitter, the sender or the receiver?
The receiver. RFC 3550 defines it by comparing spacing at the receiver with spacing at the sender, and the value is reported back in reception reports.
Related terms and guides: MOS, WebRTC vs SIP phones, Softphone WebRTC, affidabilità della piattaforma.
Fonti
- RFC 3550, RTP: A Transport Protocol for Real-Time Applications (section 6.4.1, sender and receiver report packets) (source, checked November 7, 2026)
- RFC 3551, RTP Profile for Audio and Video Conferences with Minimal Control (source, checked November 7, 2026)
Letture correlate: SIP one-way audio: a step-by-step troubleshooting guide · Voice codec (G.711, G.729, Opus) · Session Border Controller (SBC)
Letture correlate: How to Measure VoIP Call Quality (MOS, Jitter) · AI Voice Agent Latency: What Callers Notice · What Is RTP (Real-time Transport Protocol)? · What Is Packet Loss in VoIP Calls? · What Is Latency in VoIP and Voice AI?
Letture correlate: What Is VoIP QoS? Quality of Service
Termini correlati
What Is Latency in VoIP and Voice AI?
Latency is the delay between speaking and being heard. See what ITU-T G.114 says on one-way delay, how it differs from jitter, and why voice AI needs it low.
Cos'è il MOS (Mean Opinion Score)?
Il MOS valuta la qualità audio da 1 a 5. Scopri come si stima sul traffico live, cosa causa un punteggio basso e perché contano i punteggi per chiamata.
Che cos'è l'architettura multi-tenant?
L'architettura multi-tenant serve molti clienti da un'infrastruttura condivisa con isolamento forzato. Come funziona, dove si applica, cosa varia.
What Is NAT Traversal? STUN, TURN and ICE
NAT traversal lets voice and WebRTC media cross routers that hide private addresses. Learn how STUN, TURN and ICE fix one-way audio for browser-based agents.
What Is Network Effectiveness Ratio (NER)?
Network effectiveness ratio (NER) measures how often the network did its job, counting busy and declined calls as successes. See the SIP formula and example.
Cos'è l'NPS (Net Promoter Score)?
L'NPS è promotori meno detrattori sulla domanda di raccomandazione da zero a dieci. Scopri come si calcola, il suo intervallo e come differisce dal CSAT.
Pronti a vedere DialerBee in azione?
Richiedi una demo dal vivo di 15 minuti oppure avvia una prova gratuita di 14 giorni: niente slide, nessun impegno. Le chiamate partono quando il tuo trunk SIP o PBX è collegato e approvato.
Prova gratuita di 14 giorni · credito IA gratuito · senza carta · 11 lingue · BYOC · controlli a supporto della conformità